Intended use and baseline construction
This SKU suits soft-hand outdoor retail, picnic assortments, parks, festivals and gift-with-purchase programs where comfort and packability matter more than expedition-grade ground protection. The phone pocket should be specified either as a flat-use convenience feature only or as a retention feature during carrying. That choice changes panel material, reinforcement, test loads and return risk.
State the construction on the PO in layer order. In this guide, 230gsm refers to the fleece face fabric only, measured before lamination or assembly unless otherwise agreed. A common build is: face fabric 230gsm recycled polyester polar fleece; backing 190T polyester with PU coating or 210D polyester with PU coating; binding 25-32mm finished width; optional PP or polyester webbing handle; optional belly band, insert card or polybag.
For a commercial baseline, specify: finished size 145 x 180cm or 150 x 180cm; fleece face 230gsm ±5% pre-assembly; 190T backing roughly 55-70gsm before coating or 210D backing roughly 95-120gsm before coating; PU coating add-on about 18-30gsm on 190T or 25-40gsm on 210D; finished piece weight tolerance ±5% per piece excluding retail inserts unless otherwise stated; lot average tolerance within ±3%. If accessories such as straps, handles, patches or paper cards are included in piece weight, write that directly into the PO.
If the brief is moving toward a groundsheet-first item rather than a comfort-first blanket, benchmark against heavier constructions instead of stretching this SKU beyond its design window. Relevant comparison reads are `190t-polyester-shell-picnic-blankets-with-100gsm-needle-punched-fillin`, `210d-nylon-ripstop-picnic-blankets-with-60gsm-polyester-padding-quilti`, `370gsm-recycled-polyester-sherpa-picnic-blankets-with-210d-pu-backing-`, `420d-oxford-2mm-epe-foam-picnic-mats-at-150x200cm-fob-carton-planning-`, and `600d-rpet-oxford-picnic-mats-with-5mm-xpe-foam-core-grs-claim-scope-ro`.
Mandatory PO requirements
Separate mandatory requirements from optional upgrades. Mandatory points should control fit for use, legal labeling, claims risk, inspection outcome and ex-factory release. For this SKU that includes construction, pocket orientation, measurement rules, seam build, hydrostatic threshold, care label text, barcode placement, fold method, carton pack-out and recycled-claim document set.
A PO-ready minimum requirement list should cover: finished size and tolerance; whether size is measured edge-to-edge including binding; face GSM tolerance and whether measured pre-assembly or on finished composite; backing specification with coating type and add-on range; finished piece weight tolerance; binding material and finished width; fold method; pocket size, placement and opening direction; stitch type, SPI and seam allowance; thread type and Tex range; bartack dimensions and locations; handle dimensions if fitted; packaging materials; carton quantity; inspection level; and pre-shipment documents.
Define measurement conditions to avoid argument later. Recommended wording: all dimensional checks after conditioning for at least 24 hours in a standard textile atmosphere of 20 ±2°C and 65 ±4% relative humidity; blanket laid flat without tension; size measured edge-to-edge including binding at the midpoint of each side; tolerances apply per piece unless a separate lot-average tolerance is stated. If a retailer measures excluding binding, state that explicitly because edge treatment can shift the result by 10-20mm.
For labeling, require country of origin, fibre content by component, care wording, PO or batch traceability code, and approved recycled-claim wording. Example: face 100% recycled polyester; backing 100% polyester; binding 100% polyester. Avoid generic 'RPET blanket' wording unless legal review for the destination market is complete and chain-of-custody records support the claim. If the channel requires consumer packaging, also specify polybag thickness, suffocation warning text, barcode format and barcode position. Useful adjacent references are `blanket-care-washing-guide`, `cross-border-e-commerce-packs-for-150gsm-microplush-throws-polybag-bar`, and `fba-ready-180gsm-microfleece-throws-with-suffocation-warning-polybags-`.
Measurement points and tolerances
Put the critical dimensions into a spec table on the PO, PPS sheet or approved master sample. Blanket and pocket disputes usually start with vague measurement points rather than poor sewing. Use the fleece face as the visual reference side unless the pocket is intentionally mounted on the backing side.
A practical measurement table for a 150 x 180cm style is: finished blanket size 1500 x 1800mm, tolerance ±20mm per piece after conditioning; binding finished width 28mm ±2mm; pocket finished panel size 125 x 205mm ±5mm; usable pocket opening width 105-115mm; pocket placement 80mm from finished side edge and 90mm from finished bottom edge to seam line, tolerance ±5mm; retail folded size 380 x 250mm ±15mm; handle cut length 420mm ±10mm; handle inside span 140mm ±10mm; export carton quantity 10 pcs unless otherwise agreed.
For the phone pocket, define the usable internal envelope, not only the cut panel size. A realistic target is to fit a device envelope up to 82 x 168 x 12mm including a slim case. If the product brief needs larger phones, widen the pocket or change its orientation instead of relying on fabric stretch. Stretch fit on fleece or thin coated fabric drives mouth waviness, corner stress and consumer complaints.
If the blanket is sold folded with the pocket visible, specify face-out orientation, logo direction and nap direction. Mixed nap direction within one carton can create apparent shade variation on dark fleece under store lighting even if dyelot is the same. For presentation-critical retail orders, require consistent nap direction within each carton and no pile crush marks on the front fold panel after 24 hours recovery.
190T versus 210D backing: what changes in practice
The choice between 190T and 210D changes abrasion life, stitch holding, fold bulk, handfeel and cost. Typical 190T polyester backing is lighter and more flexible, often about 55-70gsm before coating, and works for entry and mid-tier seasonal programs where the blanket is carried by a separate handle and the phone pocket is used mainly while the blanket is laid flat. Typical 210D backing is heavier, often about 95-120gsm before coating, and gives better stitch retention, corner durability and abrasion resistance around binding and pocket zones.
In sewing, 210D is usually more forgiving. It distorts less under stitch tension, so seam grin and pocket skew are easier to control. 190T can still perform well, but it needs tighter process control: seam allowance should not run narrow, SPI should not be excessive, and feeding of coated fabric should be even to avoid drag puckering. On dark 190T or high-coating-add-on styles, needle marks and perforation lines also show more easily.
From a commercial standpoint, 210D generally increases material cost, fold bulk and carton weight. It can also extend lead time if the backing colour must closely match the fleece or if the mill route is dyed-and-coated to order rather than stocked greige. Use 210D where the retail claim includes repeated outdoor use, rougher ground contact or stronger perceived quality. Keep 190T for softer handfeel and sharper opening price. If waterproofness is the main selling point rather than softness, compare with `900d-polyester-picnic-blankets-with-pvc-free-tpe-backing-cold-crack-re`, `tpu-laminated-190gsm-suede-finish-picnic-mats-hydrostatic-resistance-s`, and `waterproof-picnic-mat-backing-options-peva-vs-oxford-pvc-for-retail-pr`.
Pocket engineering and buyer-ready construction spec
The fold-out phone pocket is the highest-risk zone on this SKU because a small stitched panel interrupts a soft face and transfers stress into a coated backing. Typical failures are upper-corner seam opening, mouth waviness, puckering from feed mismatch, skewed placement, pile crush around the panel, coating puncture, and visible needle damage lines. These should be written into the specification as measurable acceptance criteria, not left as subjective appearance comments.
A practical standard pocket spec is: pocket on fleece face side unless otherwise approved; finished panel size 125 x 205mm ±5mm; usable device envelope up to 82 x 168 x 12mm; panel material either self-fabric laminated to a light support interlining for visual match, or backing-side fabric for better stability. In production, backing-side fabric is usually safer: 190T PU-coated polyester panel on a 190T-backed blanket, or 210D PU-coated polyester panel on a 210D-backed blanket. Mouth opening on the short side unless the approved sample uses vertical orientation.
Quantify the seam build. Recommended mouth hem 15-18mm double turn if the pocket panel is woven backing fabric; if self-fabric fleece is used, bind or fold with support tape because a raw folded fleece mouth is unstable. Side and bottom seams: 301 lockstitch, 8-10 SPI on 190T panel and 7-9 SPI on 210D panel, tolerance ±1 SPI. Seam allowance: 10-12mm on sides, 12mm on bottom, minimum 10mm maintained at corners. Thread: continuous-filament polyester Tex 27-40. Needle: NM 80/12 for lighter 190T assemblies, NM 90/14 for 210D or heavier thread, subject to approved sewing trial. Reinforcement patch behind each upper corner: 30 x 30mm minimum, 120-180gsm woven or nonwoven support patch, fused or sewn depending build approval. Bartacks: one at each upper corner, 10-12mm finished length, about 28-42 stitches per tack, positioned 3-5mm below the mouth turn and 2-4mm inboard from the side seam. For higher-retention claims, add one central mouth stay stitch or a concealed 8-10mm hook-and-loop tab, but only if the consumer brief supports the extra bulk.
Set visible quality limits for the opening. Maximum mouth waviness or puckering should not exceed 3mm peak-to-valley over any 100mm span, measured after conditioning on a flat table. Pocket skew from approved placement should not exceed 5mm in either axis. Seam grin should not expose more than 1mm of seam line over any continuous 30mm segment. Pile crush or press mark larger than 20 x 20mm in the visible folded retail face area is rejectable if not recovered after 24 hours conditioning. If the pocket is mounted on the backing side, run an explicit usability review because consumers often miss the feature and upward-facing openings can admit moisture during ground use.
Pass or fail test methods for this SKU
Do not approve this item on construction notes alone. Add pass/fail methods with conditions and test direction. For seam strength on the pocket assembly, a common approach is ISO 13935-2 strip method on the sewn seam, with load applied along the seam line; set a minimum seam strength target such as 120N for 190T pocket assemblies and 160N for 210D pocket assemblies, subject to brand risk tolerance. For seam slippage risk on the backing fabric near the pocket, use ISO 13936-2 where relevant and state a maximum seam opening under a defined load, for example not over 6mm at 180N on lightweight backing fabrics. Where the buyer prefers ASTM references, keep the method consistent across approvals.
For hydrostatic resistance of the backing or finished assembly, specify ISO 811 or AATCC 127 and state whether the sample is taken before sewing, after sewing away from seams, or on the finished sewn blanket. For this SKU, testing the backing fabric before sewing is useful for material control, but finished-goods testing after sewing and after one domestic wash is better for claim control. On stitched zones, some loss versus base fabric is normal. If a blanket is marketed as water-resistant rather than waterproof, write that wording precisely on packaging.
For colorfastness, specify at least wash fastness to ISO 105-C06, rubbing fastness to ISO 105-X12, and if the blanket is intended for outdoor sunlight exposure, light fastness to ISO 105-B02. A workable baseline is wash fastness minimum grade 4 for colour change and 3-4 for staining on the approved adjacent fibres after one cycle appropriate to the care label; dry rubbing minimum grade 4 and wet rubbing minimum grade 3 on dark shades; light fastness usually grade 4 minimum for seasonal programs and grade 5 preferred for longer-life outdoor ranges. For dimensional stability after washing, use ISO 6330 laundering with measurement to ISO 5077, and set finished blanket shrinkage or growth not exceeding 3% in either direction after the agreed wash cycle.
For coating adhesion or film integrity, specify a practical method the lab can run consistently. If the backing is PU-coated woven polyester rather than a laminated film, use an agreed internal adhesion or rub test and visual assessment after flexing; if there is a laminate, peel strength can be specified in N/25mm. In either case, write the failure mode: no cracking, flaking, tackiness migration or obvious coating transfer after the agreed conditioning and flexing. For needle damage control on coated backing, add a wet blotting or light-column check on pocket and binding seams: no continuous leakage line, no cut-like perforation track, and no coating split visible longer than 10mm along any seam. This criterion is often more useful to buyers than abstract needle wording because it ties directly to end-use risk.
For pocket function, add a simple applied load test on the finished blanket: approved device dummy mass 250-350g placed in the pocket for 1 hour while the blanket hangs from the normal fold orientation or is lifted and carried a short distance. Pass criteria: no seam break, no bartack failure, no increase in pocket skew beyond 3mm, and no permanent mouth distortion above the approved visual limit. If the brand makes no carry-phase retention claim, keep this as an internal engineering check rather than consumer-facing performance copy.
Hydrostatic targets by use case and backing choice
Replace vague 'hydrostatic requirement' language with target ranges tied to use case. For soft-hand picnic blankets with 190T PU-coated backing sold mainly for dry grass or park use, a reasonable material target is around 300-600mm hydrostatic head by ISO 811 or AATCC 127 before sewing. That gives splash and damp-grass resistance, but not kneeling pressure protection on saturated ground. For stronger ground contact expectations, 210D PU-coated backing is usually specified in the 800-1500mm range before sewing.
If the product story includes beach, campsite or cooler-ground use where the consumer expects better moisture blocking, set the finished backing material target closer to 1000-1500mm on 210D and note that sewn seams and needle zones may perform below the base fabric. If the style uses TPU lamination or heavier barrier builds, higher results are possible, but they increase cost and can stiffen handfeel. For commodity fleece picnic blankets, chasing very high hydrostatic head without reworking the whole construction often creates more problems than value, especially with fold bulk and coating brittleness.
State clearly whether the acceptance threshold applies before sewing, after sewing, or after washing. A practical buyer rule is: base backing fabric meets the specified hydrostatic range before sewing; finished blanket, tested away from seams after one agreed home-laundry cycle, should retain a meaningful percentage of that performance and show no leakage through obvious coating damage. If the marketing copy uses 'waterproof', tighten the threshold and legal review; if the copy uses 'water-resistant', align the threshold and avoid overclaiming. Related material references include `pfc-free-water-repellent-finish-on-210gsm-polyester-picnic-blankets-c0`, `pu-coated-210d-polyester-picnic-blankets-at-145x180cm-reach-svhc-check`, and `picnic-blanket-backing-peva-pu-tpu`.
Recycled claims: what is actually being certified
Use recycled terminology carefully. 'Recycled content' is a fibre claim. 'RPET' is market shorthand for recycled polyester, often from bottle-derived feedstock, but it is not a certification by itself. Chain-of-custody certification applies to specific certified components and documents, not to a product name alone.
Write the claim by component. Example: fleece face fabric contains 100% recycled polyester; backing, binding, thread, webbing and packaging are conventional unless otherwise specified. If only the fleece is certified, do not describe the whole blanket as fully certified recycled product. Non-certified trims can be allowed on many programs, but the claim wording and transaction documents must reflect that scope accurately. Some buyers accept a certified main fabric with non-certified accessories; some require all textile components within the claim scope to be certified. Check before PO issue rather than during shipment booking.
If chain-of-custody is required, specify the route and documents upfront. For example, if the buyer asks for GRS or RCS, define whether the certification must cover only the fleece fabric or the finished product assembly, and whether a transaction certificate is required per shipment. Also state whether paper packaging claims such as FSC apply separately. Good background reads are `grs-certified-200gsm-rpet-polar-fleece-travel-blankets-with-compressio`, `grs-transaction-certificate-workflow-for-250gsm-rpet-sherpa-throws-lot`, `rpet-polar-fleece-blankets-with-grs-certification-documentation-buyers`, and `textile-certifications-explained-buyers`.
Compliance and safety for main destination markets
For the US and EU, the buyer should at minimum review restricted substances, fiber labeling, care labeling and any channel-specific packaging rules. On polyester fleece and coated backing builds, common chemical screens include azo amines where relevant, disperse dyes on synthetics if the retailer requests them, formaldehyde, lead and phthalates in prints or soft PVC components if any, and REACH SVHC review for coated or printed parts sold into Europe. If the product is marketed for children, requirements tighten further and should not be assumed from an adult picnic blanket specification.
For US retail, CPSIA is relevant if the item is sold as a children's product, not simply because it is soft textile. If it is adult general-use outdoor product, use care and fiber labeling rules applicable to textiles and packaging warnings where required. If children's positioning, add tracking label obligations and age-appropriate review; `cpsia-tracking-labels-for-240gsm-printed-coral-fleece-kids-blankets-ba` is useful background. For EU retail, align with REACH restricted substance expectations and accurate fiber labeling by component.
The phone pocket itself usually does not create an entrapment hazard if it is a flat stitched pocket without cords, loops or elastic openings. If the pocket includes a flap, drawcord, elastic or closure intended for children's products, run a specific safety review. If the blanket is marketed with a phone pocket, make sure care and warning copy does not imply that electronics remain protected from impact or immersion unless the construction has actually been tested for that claim. Related compliance reads include `azo-dye-testing-for-300gsm-yarn-dyed-acrylic-throws-restricted-amine-r`, `en-71-3-tested-240gsm-coral-fleece-baby-throws-what-toy-safety-buyers-`, and `oeko-tex-standard-100-for-custom-fleece-blankets-class-ii-vs-class-i-r`.
Stage-gate approval flow before shipment
A usable sourcing flow for this SKU has five gates. Gate 1 is proto approval: approve construction concept, handfeel, fold logic, pocket orientation and target cost direction. Gate 2 is lab dip and material approval: approve fleece colour, backing colour, binding shade, coating route, and any recycled-claim scope by component. Gate 3 is PPS approval: approve one pre-production sample in bulk materials, bulk sewing method, final labels and final pack. Gate 4 is inline inspection: check first output and mid-line control. Gate 5 is final inspection and document release before ex-factory.
At proto stage, focus on whether the pocket should be self-fabric for softer retail appearance or woven panel for better stability. At PPS stage, freeze the actual construction and do not allow operator-floor substitutions such as narrower seam allowance, lighter panel fabric or shorter bartacks. For inline, inspect at least early-line and mid-line checkpoints with a pocket-specific checklist: placement, opening direction, bartack count, mouth waviness, backing needle damage, fold presentation and barcode placement. On a long run, inspect at minimum the first packed carton from each sewing line and each pack line.
For final inspection, many buyers use AQL 2.5 for major and 4.0 for minor defects on home textiles, but the exact plan should match the channel and claim profile. If the phone pocket is a featured selling point, keep its functional failures as major defects and safety or legal labeling failures as critical defects. A useful reference is `aql-2-5-inspection-checklist-for-200gsm-coral-fleece-promotional-blank`, together with `blanket-quality-control-inspection`. Before ex-factory release, require the shipment set: approved PPS record, final inspection report, packing list, commercial invoice, carton barcode verification if applicable, care and label artwork approval, test reports as agreed, and any recycled transaction documents or scope evidence required by the PO.
Defect taxonomy for inspection
Use a compact defect taxonomy so the factory, third-party inspector and buyer all classify the same problem the same way. Critical defects usually include incorrect legal labeling, missing origin label, wrong barcode causing non-scan, prohibited substance failure, mold or contamination, and any sharp foreign object or broken needle issue if metal control is required. These are shipment blockers rather than negotiable aesthetics.
Major defects on this SKU typically include: pocket skew beyond 5mm from approved placement; wrong pocket opening direction; missing bartack; broken seam; seam opening above 2mm before testing; seam grin above the agreed limit in a visible area; coating puncture or split causing leakage path; mixed nap direction within the same retail pack where appearance consistency is specified; hydrostatic or wash result below the agreed threshold; handle or binding insecure attachment; and pack-out or barcode placement differing from approved retail standard.
Minor defects usually include light recoverable pile crushing outside the main fold face, slight mouth waviness within reject limit, small pressure marks that recover after conditioning, minor thread ends, slight binding width variation within tolerance, or fold presentation drift that does not affect scanability or shelf appearance. Write packaging defects into the taxonomy as well: crushed belly band, scuffed print, missing suffocation warning, wrong carton mark, mixed size ratio, or damaged polybag seal. If the program is e-commerce, packaging faults can move from minor to major because they drive direct returns.
MOQ, cost drivers and lead-time impact
For most cut-and-sew fleece picnic blanket programs, MOQ is driven more by dyed fabric colour, backing route and packaging complexity than by sewing itself. A straightforward fleece plus stocked black 190T backing in simple belly-band pack may start at a lower practical MOQ, while custom colour 210D backing, certified recycled route, printed insert card and stricter testing push the minimum up. If the buyer needs mixed colours, the usable MOQ per colour is often the real constraint, not the total PO quantity. See `low-moq-startup-blanket-sourcing` and `picnic-blanket-moq-pricing-2026` for planning context.
The largest cost drivers on this SKU are usually fleece weight and recycled route, backing choice, coating add-on, pocket construction, handle and fold method, packaging, and certification paperwork. Moving from 190T to 210D usually raises material cost and carton weight. Adding reinforcement patches, longer bartacks, tighter inspection, or a higher hydrostatic target also costs money, though usually less than dealing with returns. Certification route can add both direct cost and schedule risk if the chain-of-custody documents are not lined up before bulk cutting.
Lead time is also sensitive to these choices. A plain blanket with standard label pack may move faster than a pocketed blanket with custom carding because PPS review often catches pocket usability issues late. Certification route can add time for transaction documents. Retail polybag with warning text and barcode sticker is usually quicker than a fully printed carton or gift pack, but each channel has its own compliance burden. If schedule is tight, freeze pocket dimensions and packaging artwork early and avoid changing backing denier after lab approval. Adjacent planning reads are `custom-blanket-lead-times-shipping`, `fca-shanghai-mixed-sku-consolidation-for-130x170cm-fleece-throws-upc-s`, and `ddp-uk-costing-for-260gsm-brushed-polar-fleece-blankets-with-printed-b`.
Model spec sheet and sample PO clauses
A compact model spec sheet for this SKU can read as follows: finished size 150 x 180cm edge-to-edge including 28mm binding; face fabric 230gsm recycled polyester polar fleece, tolerance ±5%; backing 210D polyester PU-coated, base fabric 100-115gsm, hydrostatic head 1000mm minimum before sewing by ISO 811; pocket panel 210D PU-coated polyester, finished size 125 x 205mm; pocket opening short side with 16mm double-turn hem; side and bottom seams 301 lockstitch, 8 SPI target; seam allowance 10-12mm; two upper-corner bartacks 10mm; thread polyester Tex 30; finished piece weight ±5%; wash fastness ISO 105-C06 grade 4 minimum for colour change; dimensional change after one agreed home-laundry cycle to ISO 6330 and ISO 5077 not over 3%; final inspection AQL 2.5 major, 4.0 minor unless otherwise stated.
Sample PO clauses can be short and enforceable. Clause 1: dimensions measured after 24-hour conditioning at 20 ±2°C and 65 ±4% RH, laid flat without tension, edge-to-edge including binding. Clause 2: any substitution of backing denier, pocket panel material, reinforcement patch, seam allowance, thread size or packaging material requires written buyer approval before bulk use. Clause 3: recycled claims shall be limited to components supported by valid chain-of-custody documents and approved wording. Clause 4: final shipment release requires approved PPS, passed final inspection, agreed test reports, and all label and barcode checks passed. Clause 5: pocket function and appearance shall conform to approved sealed sample; mouth waviness above 3mm per 100mm span, missing bartack, or pocket skew above 5mm is rejectable.
If the buyer wants more robust comparison before issuing the PO, compare this construction against `145gsm-190t-polyester-pocket-picnic-blankets-with-corner-sand-anchors-`, `220gsm-polyester-polar-fleece-blankets-with-self-fabric-carry-loops-lo`, `280gsm-cotton-double-gauze-picnic-blankets-with-tpu-moisture-barrier-l`, and `sand-free-beach-mat-construction` to decide whether the program priority is softness, barrier performance, or packability.
Frequently asked
What does 230gsm mean on this picnic blanket? On a clear tech pack, 230gsm should refer to the fleece face fabric only, measured before lamination or assembly unless otherwise stated. Buyers should also specify backing GSM or denier, coating add-on, and finished piece-weight tolerance because finished blanket weight can vary materially even when the fleece face is the same.
Is 190T backing good enough, or should I upgrade to 210D? 190T works for softer, lighter, sharper-priced seasonal picnic blankets used mainly on dry grass or park surfaces. 210D is usually the better choice if you want stronger stitch holding, lower seam distortion around the phone pocket, better abrasion resistance and higher waterproof targets. The trade-off is higher cost, more fold bulk and slightly stiffer handfeel.
How should the phone pocket be constructed to avoid returns? Treat it as an engineered component, not decoration. Specify panel material, opening direction, mouth hem, seam allowance, stitch density, reinforcement patch, bartack count and location, plus visual limits for waviness and skew. A stable woven pocket panel using the backing-side fabric is usually lower risk than a self-fabric fleece pocket unless appearance is the overriding priority.
What hydrostatic head should I ask for? For a comfort-first fleece picnic blanket with 190T PU-coated backing, around 300-600mm before sewing is common for damp-grass resistance. For stronger outdoor use with 210D backing, around 800-1500mm before sewing is more practical. State whether testing is on backing fabric before sewing, on finished goods away from seams, and whether results must hold after one wash.
How should recycled claims be written on labels and documents? Write recycled claims by component. If only the fleece face is recycled and certified, say that. Do not describe the whole blanket as certified recycled unless the finished product and all claimed components are within the certification scope. If the buyer requires GRS or RCS, define whether the requirement covers fabric only or the finished assembled product, and whether a transaction certificate is needed per shipment.
What inspection level is typical for this SKU? Many buyers use AQL 2.5 for major defects and 4.0 for minor defects on home textile programs, but the correct plan depends on channel and claim profile. For this SKU, pocket function failures, wrong pocket orientation, major seam issues, barcode failures and legal labeling errors should be classified clearly in the defect list before bulk production starts.
Have a project in mind? Send us your spec — we'll reply within one business day with indicative pricing and a sample plan.